14.97 – 80.01 Range
- Black Gildan 100% cotton T-shirt with U.S. Snipers Spade logo on back measuring about 12” high with a small 3” round U.S. Snipers logo on front left chest. The spade logo was a co-op job. Mike McMillan of CSM Gear suggested using the spade and our artist came up with the lettering and design.
- Sand Gildan 100% cotton T-shirt with line art on the back of a SF sniper in Fallujah with text, “Converting terrorist one bullet at a time.” Features 3” round US Snipers logo on front left chest. Line art measures about 14” wide and created by a young lady free hand from a photo supplied by a member of the Special Forces.
- The “We Support Diplomacy” shirt features a rifle of our design being supported by our Accu-Shot PRM Monopod and PSR Atlas Bipod with Spiked Cleated Feet. Text reads, "We Support Diplomacy” with “the last 600 yards of” in a smaller font between “Support” and “Diplomacy”.Artwork and text are white printed onto a navy Gildan 100% cotton T-shirt. The front has a “B&T” circle logo on the front chest with “Bitter & Twisted” below.
- Grey Gildan 100% cotton T-shirt with “B&T” circle logo on the front chest with “Bitter & Twisted” below. On the back is the image seen with the following phrase in both English and Chinese:
We just want to make sure the thieves know…Atlas Precision Bipods® & Accu-Shot Precision Monopods® registered trademark patent owner is B&T Industries L.L.C...All B&T products are made in the USA and we are proud of it.
- The BT56 LD 1/4-20 Adapter is a mounting solution to interface between a Tripod or similar supporting device (shooting/walking/camera stick type monopod) with a standard ¼-20 threaded stud and a firearm.Once the BT56 is installed on your supporting device using the ¼-20 threaded hole found on the BT56, the other side will accept ant 17S size Picatinny lever or ARCA mount with the matching two hole pattern of 1.100” and 10/32 threaded holes. After completed with a mount or your choice, your Picatinny or ARCA rail equipped Rifle, Pistol or Shotgun can be quickly mounted and held to your supporting device.This is a great option for getting added support for hunting and tactical situations where a bipod is not practical. The BT56 LD will hold your supporting device to the firearm for transitioning or relocation of firearm.It is machined from 6061-T6 aluminum that is Mil-Spec Type III hard anodized. No hardware included. Available in black only.The Picatinny Rail lever mount is NOT included. However, the BT56 LD and ADM-170-S can be ordered together as our BT56 LD-L. Other compatible options we currently offer are Area 419's ARCALOCK Clamp and Arisaka's Picatinny Rail Slider.Weight: 0.8 ounces
- Mint Green Gildan 100% cotton T-shirt with “B&T” circle logo on the front chest with “Bitter & Twisted” below. On the back is artwork featuring a single daisy flower and line art of a rifle in our design with our BT46-LW17 PSR Atlas Bipod and BT74 Raider Cleat feet and a BT12-QK Accu-Shot Monopod installed with the words "Daisy If You Do." Image and words are in yellow ink. Original artwork.
- The BT32 Atlas Standard Rubber Feet are standard equipment on all V8, PSR or CAL series Atlas Bipods. They will also fit bipods/adapters that use Atlas feet. Easily installed with the press of a stainless steel plunger. Sold as a pair. Available in black only.Weight: 1.0 ounce
- U.S. Snipers Sign reads, “No Trespassing Live Fire Range.” It measures 10 x 14" with two 1/4" holes centered top and bottom and are .063 thick Aluminum with a reflective background.
- The front of the “Support in Retro” shirt features a rifle of our design supported by our PSR Atlas Bipod with the new Atlas Raider Cleat Feet and B&T logo. The back features the buttstock from the same rifle supported by our Accu-Shot PRM Monopod.Artwork and text are yellow printed onto a navy, Gildan 2400 Ultra Cotton long sleeve shirt.
- Sale!The BT20B Atlas Accuracy International Spigot Bottom Rail is the same rail found in the BT20, but consists of the bottom 1913 rail ONLY. It attaches to the BT19 AAIS on the bottom and accepts any rail mounted bipod. It will also attach to many ARCA rail adaptors currently on the market with the same two hole pattern of 1.100” to the ARCA rail and accept any rail mounted bipod.It is the same rail found on our BT21 TRG Bracket and BT43 Leveraged Rail. It will also attach to the ARCALOCK Clamp.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. NO HARDWARE INCLUDED. Available in black only.
- Length: 1.60"
- Weight: 0.57 ounces
- Sale!The BT34 - 2.05" 1913 Picatinny Rail has a center to center spacing of 1.6". Two machine screws can be used not included, see BT1517) to attach this rail to the forearm of standard rifle stocks. It can also be attached to a horizontal surface on the Butt section to attach our Precision Rail Monopods.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. NO HARDWARE INCLUDED. Available in black only.Weight: 0.4 ounces
- Sale!The BT49 - 2.05" 1913 Adjustable Picatinny Rail has a center-to-center spacing of 1.2 - 1.6". Two machine screws can be used (not included, see BT1517) to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish.The BT49 can also be attached to a horizontal surface on the Butt section to attach our Precision Rail Monopods. Available in black only.
- Length: 2.05"
- Weight: 0.4 ounces
- Sale!The BT15 - 3.35" 1913 Picatinny Rail will accommodate hole patterns with a center to center spacing of 1.76 – 2.78" and a relieved back to accommodate curved surfaces.A standard sling stud and sling stud spacer can be used as one fastener or two button head machine screws can be used. NO HARDWARE INCLUDED. See BT1517 to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 0.92 ounces
- Sale!The BT17 - 4" 1913 Picatinny Rail will accommodate hole patterns with a center to center spacing of 2.2 – 3.5" with a FLAT back to accommodate flat surfaces.A standard sling stud and sling stud spacer or two button head machine screws can be used as a fastener. NO HARDWARE INCLUDED. See BT1517 to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 1.20 ounces
- The BT34 - 2.05" 1913 Picatinny Rail has a center to center spacing of 1.6". Two machine screws can be used not included, see BT1517) to attach this rail to the forearm of standard rifle stocks. It can also be attached to a horizontal surface on the Butt section to attach our Precision Rail Monopods.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. NO HARDWARE INCLUDED. Available in black only.Weight: 0.4 ounces
- The BT20-B Atlas Accuracy International Spigot Bottom Rail is the same rail found in the BT20, but consists of the bottom 1913 rail ONLY. It attaches to the bottom of the BT19 AAIS via blind threaded 10/32 holes and has a two hole pattern of 1.100" (see third image).To utilize the quick detach lever on our “LW17” style of Atlas Bipods OR the 2-screw mount style of Atlas Bipods, it is compatible with the following:• Any ARCA clamp with a matching hole pattern. We offer Area 419's ARCALOCK Clamp separately OR together as a complete unit: BT20-B/ARCALOCK Clamp (see fourth image)• Any Picatinny clamp with matching hole pattern. We offer American Defense's ADM-170-S separately OR together as a complete unit: BT43 Leveraged Rail (see fifth image)• Arisaka's Picatinny Rail SliderMachined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only. NO HARDWARE INCLUDED. 10-32 x 3/8" Flathead Socket Screws available separately.
- Length: 1.60"
- Weight: 0.57 ounces
- The BT49 - 2.05" 1913 Adjustable Picatinny Rail has a center-to-center spacing of 1.2 - 1.6". Two machine screws can be used (not included, see BT1517) to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish.The BT49 can also be attached to a horizontal surface on the Butt section to attach our Precision Rail Monopods. NO HARDWARE INCLUDED. Available in black only.
- Length: 2.05"
- Weight: 0.4 ounces
- The B&T Counter Mats are 11" x 17" with round corners. Each are hard top laminated with .125" mouse pad backer and features line art of the PSR Atlas Bipod and B&T logo.
- The ARCALOCK Spigot Extension was designed for use with Area 419's ARCALOCK Clamp.Some ARMS17-S accessory with matching hole pattern of 1.100” such as American Defense's ADM-170-s, Arisaka's Picatinny Rail Slider or Really Right Stuff's BTC-Pro Bipod Clamp. However due to design, some clamps will NOT fit such as Magpul's QR Rail Grabber (MAG1196) and Really Right Stuff's SC-ARC Bipod Clamp.It is ideal to adapt our BT35-NC 5-H Atlas Bipod to an ARCA clamp for clearance of the cradle and operation of the clamp's knob. It will also extend all "NC" or No Clamp models (view complete list below) of Atlas Bipods out extra 1.25″ for increased stability. To use with your Bipod that already has a clamp, lever or mount installed, simply remove it to attach the spigot.This spigot is manufactured by Area 419 NOT by B&T Industries L.L.C. Includes two 10-32 x 3/8" flathead socket screws and two 10-32 x 5/8" flathead socket screws.
- Weight: 1.79 oz
- Dimensions: 3.2 × 1.24 × 0.35 in
- Sale!The BT28 AFAR Rail Kit will mount into accessory rails and provide a low profile 1913 Picitinny rail for attaching the Atlas Bipods or other accessories. This is a great option for shooters that have accessory rails and want to use their rail mounted Atlas on several rifles.The uniquely designed rectangle nuts (BT28-N) fit both Freeland and Anschutz style rails by rotating them 90°.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish with 4041 Alloy Steel fasteners. Includes two rectangle nuts, two (2) 10-32 x 3/8″ flat head socket cap screws and two (2) 10-32 x 1/2″ flat head socket cap screws. Available in black only.
- Length: 2.05"
- Weight: 0.89 ounces
- The BT15 - 3.35" 1913 Picatinny Rail will accommodate hole patterns with a center to center spacing of 1.76 – 2.78" and a relieved back to accommodate curved surfaces. It also has a flush cup allowing the use of Flush Cup sling swivels and sling studs (neither provided).A standard sling stud and sling stud spacer can be used as one fastener or two button head machine screws can be used. NO HARDWARE INCLUDED. See BT1517 to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 0.92 ounces
- The BT17 - 4" 1913 Picatinny Rail will accommodate hole patterns with a center to center spacing of 2.2 – 3.5" with a FLAT back to accommodate flat surfaces. It also has a flush cup allowing the use of Flush Cup sling swivels and sling studs (neither provided).A standard sling stud and sling stud spacer or two button head machine screws can be used as a fastener. NO HARDWARE INCLUDED. See BT1517 to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 1.20 ounces
- The BT26 CAR Adaptor installed on your CAR collapsible stock allows any of our Precision Rail Monopod style monopods to be installed. This is a great option for shooters that want the LOP adjustments available with a collapsible stocks, but want the stability provided by the Accu-Shot. The BT26 replaces the factory loop on the stock while providing the means to re-attach the fixed sling loop with the loop on the left, right or bottom angled forward or backward. It is made of 1018 Cold Rolled Steel and treated with magnesium phosphate. Available in black only.Weight: 1.1 ounce
