14.97 – 80.01 Range
- Black Gildan 100% cotton T-shirt with U.S. Snipers Spade logo on back measuring about 12” high with a small 3” round U.S. Snipers logo on front left chest. The spade logo was a co-op job. Mike McMillan of CSM Gear suggested using the spade and our artist came up with the lettering and design.
- Sand Gildan 100% cotton T-shirt with line art on the back of a SF sniper in Fallujah with text, “Converting terrorist one bullet at a time.” Features 3” round US Snipers logo on front left chest. Line art measures about 14” wide and created by a young lady free hand from a photo supplied by a member of the Special Forces.
- The BT15 - 3.35" 1913 Picatinny Rail will accommodate hole patterns with a center to center spacing of 1.76 – 2.78" and a relieved back to accommodate curved surfaces. It also has a flush cup allowing the use of Flush Cup sling swivels and sling studs (neither provided).A standard sling stud and sling stud spacer can be used as one fastener or two button head machine screws can be used. NO HARDWARE INCLUDED. See BT1517 to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 0.92 ounces
- The “We Support Diplomacy” shirt features a rifle of our design being supported by our Accu-Shot PRM Monopod and PSR Atlas Bipod with Spiked Cleated Feet. Text reads, "We Support Diplomacy” with “the last 600 yards of” in a smaller font between “Support” and “Diplomacy”.Artwork and text are white printed onto a navy Gildan 100% cotton T-shirt. The front has a “B&T” circle logo on the front chest with “Bitter & Twisted” below.
- The BT17 - 4" 1913 Picatinny Rail will accommodate hole patterns with a center to center spacing of 2.2 – 3.5" with a FLAT back to accommodate flat surfaces. It also has a flush cup allowing the use of Flush Cup sling swivels and sling studs (neither provided).A standard sling stud and sling stud spacer or two button head machine screws can be used as a fastener. NO HARDWARE INCLUDED. See BT1517 to attach this rail to the forearm of standard rifle stocks. Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 1.20 ounces
- The BT22 Atlas Leg Extensions are easily installed to any V8, PSR or CAL series Atlas Bipod with the press of a stainless steel plunger. They provide an additional 3 inches of elevation and accept any of our optional V8, PSR or CAL feet. They will also fit bipods/adapters that use Atlas feet. Sold as a pair. Available in black only. NSN 1005-01-641-0369Total Weight of Pair: 1.8 ounces
Product will work on V8, PSR and CAL models only.
- The BT23 Atlas Ski Feet are easily installed to any V8, PSR or CAL series Atlas Bipod with the press of a stainless steel plunger. They will lay flat in the 90 degree position only. The BT23 delivers a fully articulated smooth foot to support the bipod. They will also fit bipods/adapters that use Atlas feet. Sold as a pair. Available in black only. NSN 1005-01-640-8881Total Weight of Pair: 1.5 ounces
Product will work on V8, PSR and CAL models only.
- The BT19 Atlas Accuracy International Spigot (AAIS) is designed for use with any NC (No Clamp) style Atlas Bipod that mounts directly to the AAIS which plugs into the Accuracy International AI/AICS stocks utilizing the factory retention/release mechanism.The evolution of long range shooting and shooter's demand drove subtle changes to the BT19. The latest modification stops the 3 to 9 rotation.It is machined from 6061-T6 aluminum that is Mil-Spec Type III hard anodized mated with an alloy steel Spigot that is finished with a Manganese Phosphate. Includes two (2) 10-32 x 1" flat head socket cap screws. Available in black only.Weight: 4.7 ounces
- The BT20 Atlas Accuracy International Spigot (AAIS) Rail Set consists of three pieces of 1913 rail that can be attached to the BT19 AAIS on the bottom and both sides. This accommodates for a multitude of options including the mounting of any rail mounted Atlas Bipod.For the bottom rail only, check out our BT20-B.Each rail is machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only. Includes four (4) 10-32 x 5/8" flat head socket cap screws.
- Length: 1.6" each
- Weight: 2.2 ounces
- The BT26 CAR Adaptor installed on your CAR collapsible stock allows any of our Precision Rail Monopod style monopods to be installed. This is a great option for shooters that want the LOP adjustments available with a collapsible stocks, but want the stability provided by the Accu-Shot. The BT26 replaces the factory loop on the stock while providing the means to re-attach the fixed sling loop with the loop on the left, right or bottom angled forward or backward. It is made of 1018 Cold Rolled Steel and treated with magnesium phosphate. Available in black only.Weight: 1.1 ounce
- The BT28 AFAR Rail Kit will mount into accessory rails and provide a low profile 1913 Picitinny rail for attaching the Atlas Bipods or other accessories. This is a great option for shooters that have accessory rails and want to use their rail mounted Atlas on several rifles.The uniquely designed rectangle nuts (BT28-N) fit both Freeland and Anschutz style rails by rotating them 90°.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish with 4041 Alloy Steel fasteners. Includes two rectangle nuts, two (2) 10-32 x 3/8" flat head socket cap screws and two (2) 10-32 x 1/2" flat head socket cap screws. Available in black only.
- Length: 2.05"
- Weight: 0.89 ounces
- The BT29 Sako TRG Rail Kit comes complete and ready to install onto your TRG stock. The kit allows for the installation of the BT12-QK Accu-Shot Precision Rail Monopod (BT12-QK is shown but not included). It is machined from 6061-T6 aluminum that is Mil-Spec Type III hard anodized. Available in black only. Weight: 1.15 ouncesInstallation of the BT29 REQUIRES the temporary removal of the butt pad assembly and drilling of a second hole. Although, this can be accomplished with common hand tools, B&T Industries L.L.C. strongly recommends a competent Gunsmith install the BT29 Sako TRG Rail Kit.
- The BT30-C Coyote Brown Atlas Bipod Pouch accommodates all V8, Standard PSR and CAL model Atlas Bipods. They offer a pocket for the Atlas Leg Extensions and another for optional Atlas feet.It does NOT accept the 5-H, Super CAL or Tall PSR/CAL models.Made out of 1000 denier cordura nylon. Also available in Ranger Green and Black.Weight: 7.9 ounces
- The BT30-R Ranger Green Atlas Bipod Pouch accommodates all V8, Standard PSR and CAL model Atlas Bipods. They offer a pocket for the Atlas Leg Extensions and another for optional Atlas feet.It does NOT accept the 5-H, Super CAL or Tall PSR/CAL models.Made out of 1000 denier cordura nylon. Also available in Coyote Brown and Black. Weight: 7.9 ounces
- The BT30-B Black Atlas Bipod Pouch accommodates all V8, Standard PSR and CAL model Atlas Bipods. They offer a pocket for the Atlas Leg Extensions and another for optional Atlas feet.It does NOT accept the 5-H, Super CAL or Tall PSR/models.Made out of 1000 denier cordura nylon. Also available in Coyote Brown and Ranger Green. Weight: 7.9 ounces
- The BT32 Atlas Standard Rubber Feet are standard equipment on all V8, PSR or CAL series Atlas Bipods. They will also fit bipods/adapters that use Atlas feet. Easily installed with the press of a stainless steel plunger. Sold as a pair. Available in black only.Weight: 1.0 ounce
- The BT34 - 2.05" 1913 Picatinny Rail has a center to center spacing of 1.6". Two machine screws can be used not included, see BT1517) to attach this rail to the forearm of standard rifle stocks. It can also be attached to a horizontal surface on the Butt section to attach our Precision Rail Monopods.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. NO HARDWARE INCLUDED. Available in black only.Weight: 0.4 ounces
- U.S. Snipers Sign reads, “No Trespassing Live Fire Range.” It measures 10 x 14" with two 1/4" holes centered top and bottom and are .063 thick Aluminum with a reflective background.
- The BT21 Atlas TRG Bracket (ATB) is designed for use with the Sako TRG line of rifles that utilize the TRG bipod attachment slot with 0.42" hole spacing. The ATB provides a forward mounting position which is also closer to the bore-line.It is designed for use with either the 2-screw clamp (BT10, BT65, BT69, BT72) or quick detach lever (indicated by "LW17") models of Atlas Bipods, which would mount directly to the Picatinny Rail portion of the ATB.Although the No Clamp (NC) models can be mounted onto the ATB, it requires installation of the bipod during the installations of the ATB prior to reassembly of stock. THIS RESULTS IN A SEMI-PERMANENT, DEDICATION OF THE BIPOD TO THAT PARTICULAR RIFLE.The ATB is constructed from 6061-T6 Aluminum with a Type III hard anodized finish and heat treated alloy steel with a Manganese Phosphate finish. Available in black only. Fasteners included: two (2) M5 - .8 x 10” flat head socket cap screws, two (2) 10-32 x 3/4” flat head socket cap screws and two (2) 10-32 x 5/8” flat head socket cap screws
- Length: 3.83"
- Weight: 5.03 ounces
- The BT20-B Atlas Accuracy International Spigot Bottom Rail is the same rail found in the BT20, but consists of the bottom 1913 rail ONLY. It attaches to the bottom of the BT19 AAIS via blind threaded 10/32 holes and has a two hole pattern of 1.100" (see third image).To utilize the quick detach lever on our “LW17” style of Atlas Bipods OR the 2-screw mount style of Atlas Bipods, it is compatible with the following:• Any ARCA clamp with a matching hole pattern. We offer Area 419's ARCALOCK Clamp separately OR together as a complete unit: BT20-B/ARCALOCK Clamp (see fourth image)• Any Picatinny clamp with matching hole pattern. We offer American Defense's ADM-170-S separately OR together as a complete unit: BT43 Leveraged Rail (see fifth image)• Arisaka's Picatinny Rail SliderMachined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only. NO HARDWARE INCLUDED. 10-32 x 3/8" Flathead Socket Screws available separately.
- Length: 1.60"
- Weight: 0.57 ounces
- The BT33 Tube Rail Kit consists of a Steel Bar Nut, designed to fit inside free float tubes, and a low profile 1913 Picatinny rail 2.05" long with a 1.00" radius back and a center-to-center spacing of 1.602 between the holes.The BT33 is installed with the Steel Bar Nut inside the free float tube and the 1913 Picatinny rail on the outside with the matching holes aligned. Fastened together, they allow the attaching of the Atlas Bipod or other accessories to free float tubes.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Manganese phosphate finish on the steel bar nut. Hardware included. Available in black only.
- Length: 2.05"
- Weight: 1.3 ounces
- The BT39 AI Monopod Bracket (AIMB) is an adapter required to attach the BT08-QK ASAI monopod (used with the original “legacy” AI style stocksides) to the new Accuracy International “Gen 2” style stocksides. It is machined from 4140 steel with a manganese phosphate finish. Modification to the Buttstock Stocksides (skins) is required to accept the BT39 AIMB.The BT39 AIMB is mounted to the AI frame using your existing BT08 Stock Collar Fastener (this fastener is not included in the BT39, it is included with the BT08) being threaded to the lower AI butt pad bolt. The BT08 is then attached to the BT39 AIMB by means of the supplied 5/16-24 socket head cap screw.Weight: 5.4 ounces
- The ADM-170-S base is precision machined from 6061 T6 aluminum and finished in hard coat T3 Mil-Spec anodize. It features the Patented QD Auto Lock™ Lever system to accommodate both in spec and out of spec rail systems. It has two hole pattern of 1.100”.This lever is manufactured by American Defense MFG, LLC NOT by B&T Industries, LLC and is used on our V8, PSR, CAL and Super CAL models of Atlas Bipods. All warranty issues are to be processed through American Defense MFG, LLCWeight: 1.905 ounces
- The BT45 Savage 110BA Fore-end Rail (SFR) will mount using the existing Sling Stud bracket holes on the Savage 110BA fore-end without modification. Once installed it will provide a low profile 1913 Picatinny rail for attaching the Atlas Bipod or other accessories to your Savage 110BA.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish with 4041 Alloy steel fasteners having a Manganese Phosphate finish. Available in black only.The newer version of the Savage 110BA has a different hole spacing with a single hole and slots. We strongly recommend confirming the center-to-center hole spacing of 0.506" to ensure proper fit of the BT45. See image.
- Length: 1.6"
- Weight: 0.8 ounces
