- The BT74 Atlas Raider Cleat Feet are turned from 303 Stainless Steel bar stock in one piece for strength and durability. They will fit V8, PSR and CAL series of Atlas Bipods. They will also fit bipods/adapters that use Atlas feet. Easily installed with the press of a stainless steel plunger.The Cleat portion is approximately 1.000” long with the largest outer diameter of approximately 1.155”. Sold as a pair. Available in raw stainless steel only.NSN 1005-01-700-6502Total Weight of Pair: 2.6 ouncesProduct will work on V8, PSR and CAL models only.
- The front of the “Support in Retro” shirt features a rifle of our design supported by our PSR Atlas Bipod with the new Atlas Raider Cleat Feet and B&T logo. The back features the buttstock from the same rifle supported by our Accu-Shot PRM Monopod.Artwork and text are yellow printed onto a navy, Gildan 2400 Ultra Cotton long sleeve shirt.
- BT78: SIG SAUER® CROSS™ Buttstock Rail Kit is a 2.05" 1913 Picatinny Rail that installs directly onto the folding buttstock of the SIG SAUER® CROSS™ rifle to allow for mounting our Accu-Shot Precision Rail Monopods (BT12-QK, BT13-QK and BT31-QK).Installation requires two factory 10-24 threaded holes spaced approximately 1.57" apart as found on our sample SIG SAUER® CROSS™. No modification is required. Comes with two 10-24 x 3/4" flat socket cap screws as seen. Use of a thread locker upon installation is suggested.Machined to Picatinny rail standards from 6061-T6 aluminum with Mil-Spec Type III Class 2 finish. Available in black only.Weight: 0.56 ouncesLength: 2.05"
- The BT79 Barrett® M107A1® Rail is a 5-slotted 1913 Picatinny rail for direct installation to the Barrett® M107A1® providing the means to mount our Atlas Bipod Picatinny rail mounted bipods. It is also compatible with the Barrett® M82A1®.The center-to-center hole spacing of 3.359" fits the outer two holes of the existing three holes in the chassis. We strongly suggest that you measure the hole spacing on your rifle.The center section is machined to Picatinny rail standards from 4140 cold finished steel with a maganese phosphate finish. Two 3/8-16 x 3/4” flat head cap screws are provided.The original 11/16" nuts and tooth lock washers are reused to complete assembly. An 11/16" socket and ratchet wrench OR break-over bar and a 7/32” hex wrench is required for installation (none included). Check out installation instruction below. No modification needed.
- Overall Length: 4.309"
- Weight: 5.22 ounces
- The BT80 M-LOK® Flush Cup Rail is designed for use with all M-LOK® compatible hand guards, forends and buttstocks. It has 5 usable slots and a flush cup allowing the use of Flush Cup sling swivels and sling studs (neither provided). The BT80 can be used to attach any of our 1913 Picatinny rail mounted Atlas Bipods, Accu-Shot Monopods or Folding Foregrip. It requires standard M-LOK® sized slots for mounting.Machined from 6061-T6 aluminum and Type III hard coat anodized. It comes with two 10-24 x 3/8 fasteners and two M-LOK® nuts. Available in black only.
- Length: 2.875"
- Center-to-center: 1.575"
- Width: 0.835"
- Weight: 1.038 oz
- The BT81 Lil’ Brandi is our long awaited answer to getting a 1913 Picatinny Rail mounted on a traditional rifle stock without taking the rifle apart, drilling holes or damaging the stock. Installation utilizes the existing sling stud and provided cross pin, set screw and hex wrench.It features 3 usable slots for attaching any rail mounted Atlas Bipod and a sling attachment to utilize a sling if desired. The angular wings with rubber pads contact the stock. Machined to Picatinny rail standards from 7075-T6 aluminum with Mil-Spec Type III Class 2 finish. No disassembly required. Patent Pending.Not intended for use with flat stocks (reference fourth and fifth image). If the stock has two sling studs, we strongly recommend using our BT15 or BT17
- Dimensions: 1.95 x 1.5 x 0.663 in
- Weight: 0.89 ounces
- For anyone that wishes to apply a finish to a currently owned B&T Accu-Shot Monopod:When applying an aftermarket finish that requires the use of heat or disassembly to any B&T Accu-Shot Monopod, we respectfully ask that you send that product to us so we can properly disassemble and return all appropriate parts to you for application of the finish.Once the finish is applied and the parts are returned to B&T, we will reassemble them to our specifications and ship it back to you. Please ensure parts are packaged appropriately to avoid any damage in transit. B&T will not be responsible for the finish or any damage to the finish.Anyone that disassembles, loses, breaks parts in an attempt to disassemble or cannot reassemble their Accu-Shot Monopod will be charged $75.00 plus parts minimum.Anyone choosing not to use this service does so at their own risk and liability voiding the monopod's Lifetime Warranty.B&T Industries L.L.C. does not sell or ship replacement parts.
- For anyone that wishes to apply a finish to a currently owned B&T Atlas Bipod:When applying an aftermarket finish that requires the use of heat or disassembly to any B&T Atlas Bipod, we respectfully ask that you send that product to us so we can properly disassemble and return all appropriate parts to you for application of the finish.Once the finish is applied and the parts are returned to B&T, we will reassemble them to our specifications and ship it back to you. Please ensure parts are packaged appropriately to avoid any damage in transit. B&T will not be responsible for the finish or any damage to the finish.Anyone that disassembles, loses or breaks any parts in an attempt to disassemble/reassemble their Atlas Bipod will be charged $105.00 plus parts minimum.Anyone choosing not to use this service does so at their own risk and liability voiding the bipod's Lifetime Warranty.B&T Industries L.L.C. does not sell or ship parts.
- "Experience the blend of reliability and lightness with the BTC-Pro clamp. This screw knob clamp offers precise control, ensuring secure attachment of your equipment while shedding unnecessary weight. For photographers and outdoor enthusiasts seeking the optimal balance between strength and portability, the BTC-Pro is your ultimate companion. No compromise on durability, no added burden - that's the BTC-Pro promise." - Really Right Stuff SOAR DivisionThe BTC-Pro Bipod Clamp's Dual Combination Jaw allows for the attachment to either a Picatinny Rail or RRS 1.5" Dovetail Standard. It will bolt directly to any “NC” (No Clamp) style of Atlas Bipods (except the 5-H which requires Extension Spigot for compatibility) using provided hardware. Compatible Atlas Bipod models listed below.It will also bolt directly to our BT56LD 1/4-20 Lever Adapter.The BTC-Pro Bipod Clamp is CNC machined from 6061-T651 aluminum. Includes two (2) 10-32 x 3/8 flat-head screws and (1) 1/8" hex-key. Made in the USA.This clamp is manufactured by Really Right Stuff, SOAR Division NOT by B&T Industries, LLC. All warranty issues are to be processed through Really Right Stuff.
- Black Gildan 100% cotton T-shirt with U.S. Snipers Spade logo on back measuring about 12” high with a small 3” round U.S. Snipers logo on front left chest. The spade logo was a co-op job. Mike McMillan of CSM Gear suggested using the spade and our artist came up with the lettering and design.
- Sand Gildan 100% cotton T-shirt with line art on the back of a SF sniper in Fallujah with text, “Converting terrorist one bullet at a time.” Features 3” round US Snipers logo on front left chest. Line art measures about 14” wide and created by a young lady free hand from a photo supplied by a member of the Special Forces.
- U.S. Snipers Sign reads, “No Trespassing Live Fire Range.” It measures 10 x 14" with two 1/4" holes centered top and bottom and are .063 thick Aluminum with a reflective background.
