- Length: 3.83"
- Weight: 5.03 ounces
- The BT21 Atlas TRG Bracket (ATB) is designed for use with the Sako TRG line of rifles that utilize the TRG bipod attachment slot with 0.42" hole spacing. The ATB provides a forward mounting position which is also closer to the bore-line.It is designed for use with either the 2-screw clamp (BT10, BT65, BT69, BT72) or quick detach lever (indicated by "LW17") models of Atlas Bipods, which would mount directly to the Picatinny Rail portion of the ATB.Although the No Clamp (NC) models can be mounted onto the ATB, it requires installation of the bipod during the installations of the ATB prior to reassembly of stock. THIS RESULTS IN A SEMI-PERMANENT, DEDICATION OF THE BIPOD TO THAT PARTICULAR RIFLE.The ATB is constructed from 6061-T6 Aluminum with a Type III hard anodized finish and heat treated alloy steel with a Manganese Phosphate finish. Available in black only. Fasteners included: two (2) M5 - .8 x 10” flat head socket cap screws, two (2) 10-32 x 3/4” flat head socket cap screws and two (2) 10-32 x 5/8” flat head socket cap screws
- The BT74 Atlas Raider Cleat Feet are turned from 303 Stainless Steel bar stock in one piece for strength and durability. They will fit V8, PSR and CAL series of Atlas Bipods. They will also fit bipods/adapters that use Atlas feet. Easily installed with the press of a stainless steel plunger.The Cleat portion is approximately 1.000” long with the largest outer diameter of approximately 1.155”. Sold as a pair. Available in raw stainless steel only.NSN 1005-01-700-6502Total Weight of Pair: 2.6 ouncesProduct will work on V8, PSR and CAL models only.
- The BT79 Barrett® M107A1® Rail is a 5-slotted 1913 Picatinny rail for direct installation to the Barrett® M107A1® providing the means to mount our Atlas Bipod Picatinny rail mounted bipods. It is also compatible with the Barrett® M82A1®.The center-to-center hole spacing of 3.359" fits the outer two holes of the existing three holes in the chassis. We strongly suggest that you measure the hole spacing on your rifle.The center section is machined to Picatinny rail standards from 4140 cold finished steel with a maganese phosphate finish. Two 3/8-16 x 3/4” flat head cap screws are provided.The original 11/16" nuts and tooth lock washers are reused to complete assembly. An 11/16" socket and ratchet wrench OR break-over bar and a 7/32” hex wrench is required for installation (none included). Check out installation instruction below. No modification needed.
- Overall Length: 4.309"
- Weight: 5.22 ounces
- For anyone that wishes to apply a finish to a currently owned B&T Atlas Bipod:When applying an aftermarket finish that requires the use of heat or disassembly to any B&T Atlas Bipod, we respectfully ask that you send that product to us so we can properly disassemble and return all appropriate parts to you for application of the finish.Once the finish is applied and the parts are returned to B&T, we will reassemble them to our specifications and ship it back to you. Please ensure parts are packaged appropriately to avoid any damage in transit. B&T will not be responsible for the finish or any damage to the finish.Anyone that disassembles, loses or breaks any parts in an attempt to disassemble/reassemble their Atlas Bipod will be charged $105.00 plus parts minimum.Anyone choosing not to use this service does so at their own risk and liability voiding the bipod's Lifetime Warranty.B&T Industries L.L.C. does not sell or ship parts.
- Sale!The ADM-170-S base is precision machined from 6061 T6 aluminum and finished in hard coat T3 Mil-Spec anodize. It features the Patented QD Auto Lock™ Lever system to accommodate both in spec and out of spec rail systems.This lever is manufactured by American Defense Manufacturing NOT by B&T Industries L.L.C. and is used on our Atlas, PSR and CAL models.Weight: 1.905 ounces
- The BT19 Atlas Accuracy International Spigot (AAIS) is designed for use with any NC (No Clamp) style Atlas Bipod that mounts directly to the AAIS which plugs into the Accuracy International AI/AICS stocks utilizing the factory retention/release mechanism.The evolution of long range shooting and shooter's demand drove subtle changes to the BT19. The latest modification stops the 3 to 9 rotation.It is machined from 6061-T6 aluminum that is Mil-Spec Type III hard anodized mated with an alloy steel Spigot that is finished with a Manganese Phosphate. Includes two (2) 10-32 x 1" flat head socket cap screws. Available in black only.Weight: 4.7 ounces
- "Area 419 is always looking for ways to improve existing products when we are not developing new technologies. With the rapid growth in popularity of ARCA rails in precision rifle, we saw a need to improve this great dovetail technology to something that could be mechanically locked in place instead of just friction. If you have ever tried using a Barricade stop on an existing ARCA rail, you’ve probably also seen it slide under much pressure. Introducing the ARCALOCK Dovetail Rail System." - Area 419The ARCALOCK Clamp works on all standard ARCA/1.5" dovetail rails. It will bolt directly to any "NC" (No Clamp) style of Atlas Bipods (except the 5-H which requires Extension Spigot for compatibility). Compatible Atlas Bipod models listed below.It will also bolt directly to our BT20-B Bottom Picatinny Rail and BT56LD 1/4-20 Lever Adapter.The ARCALOCK Clamp features a proprietary two-stage screw design. Both the Clamp and Knob are machined from 6061-T6 Aluminum with Type III Hardcoat black anodized Clamp and Knob. The screw is turned from 303 stainless steel.This clamp is manufactured by Area 419 NOT by B&T Industries L.L.C. All warranty issues are to be processed through Area 419. NO HARDWARE INCLUDED.
- Weight: 2.5 oz
- "Experience the blend of reliability and lightness with the BTC-Pro clamp. This screw knob clamp offers precise control, ensuring secure attachment of your equipment while shedding unnecessary weight. For photographers and outdoor enthusiasts seeking the optimal balance between strength and portability, the BTC-Pro is your ultimate companion. No compromise on durability, no added burden - that's the BTC-Pro promise." - Really Right Stuff SOAR DivisionThe BTC-Pro Bipod Clamp's Dual Combination Jaw allows for the attachment to either a Picatinny Rail or RRS 1.5" Dovetail Standard. It will bolt directly to any “NC” (No Clamp) style of Atlas Bipods (except the 5-H which requires Extension Spigot for compatibility) using provided hardware. Compatible Atlas Bipod models listed below.It will also bolt directly to our BT56LD 1/4-20 Lever Adapter.The BTC-Pro Bipod Clamp is CNC machined from 6061-T651 aluminum. Includes two (2) 10-32 x 3/8 flat-head screws and (1) 1/8" hex-key. Made in the USA.This clamp is manufactured by Really Right Stuff, SOAR Division NOT by B&T Industries, LLC. All warranty issues are to be processed through Really Right Stuff.
- The BT56 LD-L 1/4-20 Lever Adapter is a Picatinny Rail mounting solution to interface between a Tripod or similar supporting device (shooting/walking/camera stick type monopod) with a standard ¼-20 threaded stud and a firearm with Picatinny Rail.Once the BT56 LD-L is installed on your supporting device using the ¼-20 threaded hole, your Picatinny Rail equipped Rifle, Pistol or Shotgun can be quickly mounted and held to your supporting device.This is a great option for getting added support for hunting and tactical situations where a bipod is not practical. The BT56 LD-L will hold your supporting device to the firearm for transitioning or relocation of firearm.It is machined from 6061-T6 aluminum that is Mil-Spec Type III hard anodized. No hardware included. Available in black only.To order the without the installed ADM-170-S, view the BT56 LD 1/4-20 AdapterWeight: 2.7 ounces
- The ADM-170-S base is precision machined from 6061 T6 aluminum and finished in hard coat T3 Mil-Spec anodize. It features the Patented QD Auto Lock™ Lever system to accommodate both in spec and out of spec rail systems. It has two hole pattern of 1.100”.This lever is manufactured by American Defense MFG, LLC NOT by B&T Industries, LLC and is used on our V8, PSR, CAL and Super CAL models of Atlas Bipods. All warranty issues are to be processed through American Defense MFG, LLCWeight: 1.905 ounces
- "Make Picatinny Great Again with the Patent Pending Arisaka Rail Slider. It transforms the Picatinny rail on your rifle into a multi-position sliding mount with a push button recoil lug. A unique detented knob is used to set sliding tension, accounts for out-of-spec rails, allows the mount to be removed or installed without having to slide it off the end of the rail, and can be quickly and easily tightened down for maximum precision." - Arisaka, LLCThe Picatinny Rail Slider will bolt directly to any “NC” (No Clamp) style of Atlas Bipods (except the 5-H which requires Extension Spigot for compatibility) using provided hardware. Compatible Atlas Bipod models listed below.It will also bolt directly to our BT20-B Bottom Picatinny Rail and BT56LD 1/4-20 Lever Adapter.The Rail Slider is CNC machined from stainless steel and MIL-A-8625 Type III hard coat anodized 6061-T651 aluminum. Includes two (2) 10-32 x 5/16" socket cap screws. Requires a 5/32" allen wrench for installation (not included). Recommended torque: 30 inch lbs. Made in the USA.This clamp is manufactured by Arisaka, LLC NOT by B&T Industries, LLC. All warranty issues are to be processed through Arisaka.
- Weight: 2.2 oz
- The ADM-5-H Lever base is precision machined from 6061 T6 aluminum and finished in hard coat T3 Mil-Spec anodize. It features the Patented QD Auto Lock™ Lever system to accommodate both in spec and out of spec rail systems. It has two hole pattern of 1.100”. This lever is manufactured by American Defense Manufacturing and NOT by B&T Industries L.L.C. This custom made lever is made to work with the 5-H Atlas Bipod only.Weight: 1.89 ounces
