- The BT56 LD 1/4-20 Adapter is a mounting solution to interface between a Tripod or similar supporting device (shooting/walking/camera stick type monopod) with a standard ¼-20 threaded stud and a firearm.Once the BT56 is installed on your supporting device using the ¼-20 threaded hole found on the BT56, the other side will accept ant 17S size Picatinny lever or ARCA mount with the matching two hole pattern of 1.100” and 10/32 threaded holes. After completed with a mount or your choice, your Picatinny or ARCA rail equipped Rifle, Pistol or Shotgun can be quickly mounted and held to your supporting device.This is a great option for getting added support for hunting and tactical situations where a bipod is not practical. The BT56 LD will hold your supporting device to the firearm for transitioning or relocation of firearm.It is machined from 6061-T6 aluminum that is Mil-Spec Type III hard anodized. No hardware included. Available in black only.The Picatinny Rail lever mount is NOT included. However, the BT56 LD and ADM-170-S can be ordered together as our BT56 LD-L. Other compatible options we currently offer are Area 419's ARCALOCK Clamp and Arisaka's Picatinny Rail Slider.Weight: 0.8 ounces
- The BT54 Flushcup Stud is a novel means to quickly install, move or remove accessories to a Picatinny rail, IF the accessory has a corresponding flushcup hole that aligns with the slots of the Picatinny rail. The BT54 was conceived and designed for use with our BT53 SILO. Available in black only.Weight: 1.0 ounce
- The BT03 M1-A/AR-15 Sling Stud Accessory replaces the standard Sling Loop found on many standard military style rifle stocks including the AR10, AR15 and M1A. Machined steel. Available in black only.Weight: 0.3 ounces
- The BT28-N AFAR Rail Nuts are the same nuts used with the BT28 AFAR Rail Kit. They are 4041 Alloy Steel fasteners. The uniquely designed rectangle nuts fit both Freeland and Anschutz style rails by rotating them 90°. Sold as a pair.Weight: 0.22 ounces
- The BT07 Tac-Cap is an optional steel cap that replaces the standard plastic cap found at the bottom of the monopod knob. It can damage soft surfaces and is intended for units that will experience hard surface use.Installation of the BT07 is friction-fit and requires no tools. However, we recommend permanently setting the BT07 and will do so at no additional charge when ordered along with any Accu-Shot Monopod, unless otherwise specified in the "comments" section. Available in black only.Weight: 0.35 ounces
- The M6 x 80 x 100 Long Bolt is compatible with both the BT08-QK Accu-Shot Accuracy International (ASAI) Monopod and BT57-QK Accu-Shot Accuracy International AT Monopod.It is required if additional length of pull spacers are used with Accuracy International buttstocks that our BT08-QK and BT57-QK are being installed on.If you are needing a replacement standard bolt, see our BT0857-B: M6 x 80 x 80 Replacement Bolt
- The Groupy measures groups within a 1.5” diameter. Measurements are laser cut into acrylic with a glow-in-the-dark cord attached.Shoot three to five shots. Lay Groupy over shot group. Adjust until one of the circles cross the center of the two outer most holes. Read measurement on that circle to determine group size.
- The M6 x 80 x 80 Replacement Bolt is the same bolt we send standard with both the BT08-QK Accu-Shot Accuracy International (ASAI) Monopod and BT57-QK Accu-Shot Accuracy International AT Monopod.Available as a replacement.If additional length of pull spacers are being used, see our BT0857-LB: M6 x 80 x 100 Long Bolt
- The BT1517 Rail Mounting Fastener Set is used for mounting 1913 rails and consists of two (2) 10-32 T-Nuts and two (2) 10-32 x ¾" Button Head Cap Screws. Sold as a pair.These T-nuts are commonly used by stock builders to accommodate the installation of sling studs and rails. They are typically bedded into the stock from the barrel channel side as illustrated in the third image.Weight: 0.4 ounces
- The BT14 Magpul PRS Threaded Sling Studs replace one of the four Socket Button Head Cap Screws found on the Magpul Precision Rifle Stock (PRS) with a sling stud. The threaded straps that come standard with the PRS can be reversed giving a total of 8 choices for stud placement. Each BT14 comes with two Sling Studs having 10-24 threads and black polymer spacers.
- Overall Length: 1.625"
- Length of Threaded Portion: 0.625"
- Length of Shaft Overall: 1.25"
- Weight: 0.5 ounces
- Sold as a single 10-32 x 1.25" Socket Cap Screw.Purchasing a quantity of two (2) 10-32 x 1.25" Socket Cap Screws would be ideal for use with any 2-screw clamp Atlas Bipod mounts (BT10, BT65, BT69, BT72). These are what we have used for contractual fulfillments.Purchasing a quantity of one (1) 10-32 x 1.25" Socket Cap Screw would be ideal for use with any Precision Rail Mount (PRM) Accu-Shot Monopod (BT12, BT13, BT31).
- Sold as a single 10-32 x 1.25" Clamp Bolt - Flat Head Fastener. The material is 4140 Alloy Steel with a manganese phosphate finish.Purchasing a quantity of two (2) 10-32 x 1.25" Clamp Bolts - Flat Head Fasteners would be ideal for use with any 2-screw clamp Atlas Bipod mounts (BT10, BT65, BT69, BT72).Purchasing a quantity of one (1) 10-32 x 1.25" Clamp Bolt - Flat Head Fastener would be ideal for use with any Precision Rail Mount (PRM) Accu-Shot Monopod (BT12, BT13, BT31).We have also used 10-32 x 1.25" Socket Cap Screws for contractual fulfillments available.
- Sold as a single 10-32 x 3/8" Flathead Socket Screw.These are the same screws that come installed on all "NC" (No Clamp) models of Atlas Bipods.
